Gamepad Xbox Series Controller

Xbox Series Controller

Test Status:Verified
Compatible: AndroidiOSLinuxPCXbox OneXbox S/X
Interfaces: BluetoothCableDongle
Release date: 10 November 2020
Price range: $44.99$64.95, find on: amzn.to
Cheap, but high quality
ADS
image
ThundeRobot G45
$25.83
Cheap, but high quality

Xbox Series Controller input lag comparison

The latency measurement was performed using a GPDL device.
This device is connected directly to the gamepad pins and allows you to get accurate and true calculations of the real latency.
#ConnectionModeMin.Avg.Max.Polling rate JitterOSFW
Xbox Series Controller
1DongleXinput2.266.4915.22120.93 of 125 Hz 2.32
Win 11
5.17.3202.0
2CableXinput2.126.2511.4124.78 of 125 Hz 2.29
Win 11
5.17.3202.0
3BluetoothXinput5.6510.7320.61111.44 of 125 Hz 3.51
Win 11
5.17.3202.0

Other tests

#ConnectionModeMin.Avg.Max.Polling rate JitterOSFW
Xbox Series Controller
4DongleXinput7.5 *8.13 *16.11 *122.99 of 125 Hz 1.12
Win 11
10.0.22631
5.20.7.0
5DongleXinput6.98 *8.27 *16.48 *120.93 of 125 Hz 1.51
Win 11
5.17.3202.0
6DongleXinput7.01 *8.46 *16.51 *118.24 of 125 Hz 1.9
Win 11
10.0.22631
5.20.7.0
7DongleXinput7.01 *8.61 *16.37 *116.18 of 125 Hz 2.12
Win 11
10.0.22631
5.20.7.0
8DongleXinput7.48 *9.06 *16.55 *110.41 of 125 Hz 2.71
Win 11
10.0.22631
5.21.3241.0
9DongleXinput7.5 *9.1 *16.5 *109.89 of 125 Hz 2.73
Win 11
10.0.22631
5.21.3241.0
10Cable OCXinput4.04 *7.88 *11.01 *126.83 of 125 Hz 1.24
Win 10
10.0.19045
5.21.3230.0
11Cable OCXinput4.01 *7.89 *10 *126.74 of 125 Hz 1.21
Win 10
10.0.19045
5.20.7.0
12CableXinput3 *7.9 *14.03 *126.66 of 125 Hz 1.94
Win 10
10.0.19045
5.21.3230.0
13CableXinput5 *7.95 *10.91 *125.71 of 125 Hz 1.38
Win 11
10.0.22631
5.20.7.0
14CableXinput5.59 *8 *10.51 *124.96 of 125 Hz 1.1
Win 11
10.0.22631
5.20.7.0
15Cable OCXinput6.01 *8 *10.52 *125.02 of 125 Hz 0.96
Win 11
10.0.22631
1
16CableXinput5.66 *8 *10.4 *124.93 of 125 Hz 1.07
Win 11
10.0.22635
1.1.5
17CableXinput5.49 *8.01 *10.51 *124.81 of 125 Hz 1.03
Win 11
5.17.3202.0
18CableXinput5.53 *8.01 *10.6 *124.78 of 125 Hz 1.28
Win 11
5.17.3202.0
19BluetoothController (8BitDo Receiver)3.64 *9.1 *19.77 *109.86 of 125 Hz 3.28
Win 11
10.0.22635
1.1.5
20BluetoothXinput6.51 *8.96 *16.02 *111.59 of 125 Hz 3.06
Win 11
10.0.22631
5.20.7.0
21BluetoothXinput6.55 *8.97 *15.75 *111.44 of 125 Hz 3.06
Win 11
5.17.3202.0
22BluetoothXinput14.05 *18.12 *45.52 *55.18 of 125 Hz 6.49
Win 11
10.0.22631
5.20.7.0
23BluetoothXinput29.17 *29.97 *30.88 *33.37 of 125 Hz 0.42
Win 11
Outdated
*Note: Latency with an asterisk are based on polling rate and do not represent actual input-lag.
More information

Latency

This chart shows how quickly your gamepad responds to button presses. Each point on the graph represents a test result.

  • The horizontal axis (X-axis) measures the time that has passed from pressing the button to the game responding. This time is called "latency".
  • The vertical axis (Y-axis) shows how often we got such a result, in percentages.

If you hover over a point on the graph, you'll see how long the latency was and how often it occurred.

The smaller the latency, the better. In an ideal world, as soon as you press a button on the gamepad, the action happens instantly in the game. If there's a large delay, you might press the button, but the action only happens some time later. In fast-paced games where every second counts, a high latency can become a problem.

Use this chart to figure out how fast your gamepad reacts.

Polling rate

The polling rate (also known as the report rate) in gamepads refers to how often the controller sends input information to the console or computer. It's measured in Hertz (Hz), which translates to the number of times per second the device reports its status to the computer.

For example, a gamepad with a polling rate of 125 Hz sends its status to the computer 125 times per second, or every 8 milliseconds.

The polling rate is essential in gaming for two reasons:

  1. Responsiveness: A higher polling rate means the controller communicates its state to the computer more frequently, resulting in faster and more responsive gameplay. In fast-paced or competitive games, even a slight increase in responsiveness can give players an advantage.

  2. Accuracy: A higher polling rate can also increase the accuracy of the controller. This is particularly important for devices like gaming mice, where precise movements can be critical, but it can also impact gamepads, especially in games that require accurate inputs.

However, it's important to note that a higher polling rate can also put more strain on the computer's CPU, as it needs to process inputs more frequently. Moreover, beyond a certain point, increases in polling rate may not yield noticeable improvements due to limitations in human reaction time and display refresh rates.

Jitter

Jitter is a measure of how much the gamepad's latency varies during testing. It is calculated as the standard deviation of the recorded delay times. A lower jitter value indicates more consistent latency, while a higher jitter suggests unstable performance. Low jitter is important for a smooth, responsive gaming experience.

Stick test of Xbox Series Controller

Inner Dead Zone

The inner dead zone is an important parameter for stick control. It helps avoid drift or accidental movement, but if this zone is larger than the necessary minimum, it can significantly impact aiming accuracy in games. Therefore, it is better when the inner dead zone is minimal or absent.

Gamepad Xbox Series Controller has no inner deadzones, which has which has a positive effect on aiming accuracy and micro control.

Outer Dead Zone

The outer dead zone indicates the extent to which there is an area where stick movement is not registered when fully deflected. If it's small, it indicates high stick calibration accuracy. In the case of a large outer dead zone, it significantly limits the useful range of motion and can have a negative impact on control.

The Xbox Series Controller gamepad has normal external stick dead zones (0.4mm). Its significant presence does not limit the range of motion and does not have a negative impact on control.

Stick Resolution

The stick resolution of the Xbox Series Controller gamepad has a motion resolution of 0.0024. This means that it can register 417 positions from the center point of the stick to its outermost edge. This is similar to the resolution of a monitor, where more pixels provide a clearer image. In the case of gamepad sticks, higher resolution ensures smoother and more precise control. As a rule, 125 positions are more than enough for a comfortable game.

It is important to know that some gamepads do not have a constant resolution and give out 0.0078 or 0.0150 (for example). Therefore, the number of end positions may differ from the real ones.

Asymmetry Index

The Asymmetry Index measures the difference in the left-right and up-down deflection of the joystick. A higher difference indicates worse joystick movement. The largest difference in the X and Y axis deflection is selected as the index. This indicator helps to understand the joystick's performance during small, precise movements that are critical for aiming and typically use 25-60% of the joystick's range of motion.

The asymmetry index of the Xbox Series Controller gamepad is 5.6% for the left stick and 8.2% for the right stick.
Learn more about how the measurements are made.

Circle Error

The "Circle Error" parameter determines the behavior of the stick at its extreme diagonal positions. With the Joystick Tester program, you can check how accurately the gamepad stick draws a circle in its movement. The lower the error value, the better. The Xbox Series Controller gamepad has 7.1% left circle error, and 7.2% right circle error.

Central Accuracy

The stick centering parameter indicates how well the stick returns to the central position after the player releases it. This characteristic is responsible for stick drift: the lower the Central Accuracy value, the better. The average worst position at which the joystick stops is taken as a measurement and is not touched.

In the case of the Xbox Series Controller, the Central Accuracy for the left joystick is 3.6%, and 5.5% for the right stick.

Disclaimer

All conclusions of the Xbox Series Controller gamepad are based on a single gamepad, which does not rule out the possibility that other units of this model may perform better or worse. However, this variation is usually insignificant. The test data was obtained using Joystick Tester program, and some parameters may differ in other programs.

Tested on firmware: 5.20.7.0, by John Punch

Inner Dead Zone

The inner dead zone is an important parameter for stick control. It helps avoid drift or accidental movement, but if this zone is larger than the necessary minimum, it can significantly impact aiming accuracy in games. Therefore, it is better when the inner dead zone is minimal or absent.

Gamepad Xbox Series Controller has no inner deadzones, which has which has a positive effect on aiming accuracy and micro control.

Outer Dead Zone

The outer dead zone indicates the extent to which there is an area where stick movement is not registered when fully deflected. If it's small, it indicates high stick calibration accuracy. In the case of a large outer dead zone, it significantly limits the useful range of motion and can have a negative impact on control.

The Xbox Series Controller gamepad has normal external stick dead zones (0.4mm). Its significant presence does not limit the range of motion and does not have a negative impact on control.

Stick Resolution

The stick resolution of the Xbox Series Controller gamepad has a motion resolution of 0.0024. This means that it can register 417 positions from the center point of the stick to its outermost edge. This is similar to the resolution of a monitor, where more pixels provide a clearer image. In the case of gamepad sticks, higher resolution ensures smoother and more precise control. As a rule, 125 positions are more than enough for a comfortable game.

It is important to know that some gamepads do not have a constant resolution and give out 0.0078 or 0.0150 (for example). Therefore, the number of end positions may differ from the real ones.

Asymmetry Index

The Asymmetry Index measures the difference in the left-right and up-down deflection of the joystick. A higher difference indicates worse joystick movement. The largest difference in the X and Y axis deflection is selected as the index. This indicator helps to understand the joystick's performance during small, precise movements that are critical for aiming and typically use 25-60% of the joystick's range of motion.

The asymmetry index of the Xbox Series Controller gamepad is 5.5% for the left stick and 4% for the right stick.
Learn more about how the measurements are made.

Circle Error

The "Circle Error" parameter determines the behavior of the stick at its extreme diagonal positions. With the Joystick Tester program, you can check how accurately the gamepad stick draws a circle in its movement. The lower the error value, the better. The Xbox Series Controller gamepad has 8.1% left circle error, and 7.6% right circle error.

Central Accuracy

The stick centering parameter indicates how well the stick returns to the central position after the player releases it. This characteristic is responsible for stick drift: the lower the Central Accuracy value, the better. The average worst position at which the joystick stops is taken as a measurement and is not touched.

In the case of the Xbox Series Controller, the Central Accuracy for the left joystick is 3.6%, and 5.1% for the right stick.

Disclaimer

All conclusions of the Xbox Series Controller gamepad are based on a single gamepad, which does not rule out the possibility that other units of this model may perform better or worse. However, this variation is usually insignificant. The test data was obtained using Joystick Tester program, and some parameters may differ in other programs.

Tested on firmware: 5.20.7.0, by John Punch

Inner Dead Zone

The inner dead zone is an important parameter for stick control. It helps avoid drift or accidental movement, but if this zone is larger than the necessary minimum, it can significantly impact aiming accuracy in games. Therefore, it is better when the inner dead zone is minimal or absent.

Gamepad Xbox Series Controller has no inner deadzones, which has which has a positive effect on aiming accuracy and micro control.

Outer Dead Zone

The outer dead zone indicates the extent to which there is an area where stick movement is not registered when fully deflected. If it's small, it indicates high stick calibration accuracy. In the case of a large outer dead zone, it significantly limits the useful range of motion and can have a negative impact on control.

The Xbox Series Controller gamepad has normal external stick dead zones (0.4mm). Its significant presence does not limit the range of motion and does not have a negative impact on control.

Stick Resolution

The stick resolution of the Xbox Series Controller gamepad has a motion resolution of 0.0024. This means that it can register 417 positions from the center point of the stick to its outermost edge. This is similar to the resolution of a monitor, where more pixels provide a clearer image. In the case of gamepad sticks, higher resolution ensures smoother and more precise control. As a rule, 125 positions are more than enough for a comfortable game.

It is important to know that some gamepads do not have a constant resolution and give out 0.0078 or 0.0150 (for example). Therefore, the number of end positions may differ from the real ones.

Asymmetry Index

The Asymmetry Index measures the difference in the left-right and up-down deflection of the joystick. A higher difference indicates worse joystick movement. The largest difference in the X and Y axis deflection is selected as the index. This indicator helps to understand the joystick's performance during small, precise movements that are critical for aiming and typically use 25-60% of the joystick's range of motion.

The asymmetry index of the Xbox Series Controller gamepad is 8.9% for the left stick and 8.5% for the right stick.
Learn more about how the measurements are made.

Circle Error

The "Circle Error" parameter determines the behavior of the stick at its extreme diagonal positions. With the Joystick Tester program, you can check how accurately the gamepad stick draws a circle in its movement. The lower the error value, the better. The Xbox Series Controller gamepad has 8% left circle error, and 7.8% right circle error.

Central Accuracy

The stick centering parameter indicates how well the stick returns to the central position after the player releases it. This characteristic is responsible for stick drift: the lower the Central Accuracy value, the better. The average worst position at which the joystick stops is taken as a measurement and is not touched.

In the case of the Xbox Series Controller, the Central Accuracy for the left joystick is 3.4%, and 4.7% for the right stick.

Disclaimer

All conclusions of the Xbox Series Controller gamepad are based on a single gamepad, which does not rule out the possibility that other units of this model may perform better or worse. However, this variation is usually insignificant. The test data was obtained using Joystick Tester program, and some parameters may differ in other programs.

Tested on firmware: 5.20.7.0, by John Punch

Xbox Series Controller: Pros and Cons

  • Quality

    The best choice if you play exclusively on PC or Xbox. Just remember to update the firmware.

    Comparison of Xbox Series Controller latency with other

    Users' opinion

    Add
    To add an opinion, you need to be !
    Sticks feel terrible
    2 votes
    Stick Resoulation feels amazing but very low polling rate 125hz it feels bad to
    5 votes
    High build quality
    5 votes
    Very loud Dpad
    4 votes
    Discharges quickly
    4 votes